The Cobalt Potential of the Broken Hill Project
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
Date: 3 March 2017
Number: 505/030317
THE COBALT POTENTIAL OF THE BROKEN HILL PROJECT
A review of previous exploration data from Impact Minerals Limited’s (ASX:IPT) 100% owned Broken
Hill Project has identified significant potential for cobalt mineralisation both as credits to the high grade
nickel-copper-platinum group metal (PGM) mineralisation recently discovered by the Company and as
stand alone deposits.
It is now well established that cobalt demand is forecast to grow considerably into the future due to its use
in a variety of products but in particular battery materials, high temperature and other alloys, adhesives,
magnetic materials, glass and ceramics. Accordingly exploration for cobalt either as a primary commodity
or as a by-product is warranted.
Over the past 18 months, and following its high grade nickel-copper-PGM and high grade silver-lead-zinc
discoveries at the Red Hill and Platinum Springs Prospects, Impact has quietly acquired a significant
tenement holding in the Broken Hill region covering some 517 square kilometres and about
100 kilometres of strike extent to the south of the Broken Hill Mine (Figure 1). The company is now one
of the largest landholders in this highly mineralised province.
A review of previous exploration results from Impact and previous explorers as well as mineral
occurrences named and documented by the Geological Survey of New South Wales has now shown that
Impact’s ground is prospective for three different styles of cobalt mineralisation:
1. Cobalt associated with high grade nickel-copper-PGM mineralisation;
2. Pyrite-cobalt deposits (so called Big Hill style deposits) similar to the Thackaringa Cobalt deposits
now being considered for development (three deposits totalling 33 Mt at 0.08% cobalt).
3. Cobalt commonly associated with copper in ironstones (Great Eastern style deposits) or iron-rich
cherts (Sister’s style deposits).
1. Cobalt associated with high grade nickel-copper-PGM
In previous drill campaigns at Broken Hill, Impact has discovered very high grade nickel-copper-PGM at
two prospects: Red Hill and Platinum Springs. Although not reported at the time, the mineralisation also
contains good grades of cobalt and the metal is a common by-product to nickel-copper sulphide deposits.
At the Red Hill Prospect Hole RHDH012 returned one of the highest drill intercepts for PGM’s ever
reported in Australia and this also contains significant cobalt. From 68.5 metres down-hole, the hole
returned:
1.2 metres at 0.5% cobalt, 7.4% nickel, 1.8% copper,
10.4 g/t platinum, 10.9 g/t gold, 294 g/t (9.5 ounces) palladium and 19 g/t silver,
4.6 g/t rhodium, 7.2 g/t iridium, 5.6 g/t osmium and 3.1 g/t ruthenium
26 Richardson Street West Perth Western Australia 6005
Tel +61 (8) 6454 6666 Facsimile +61 (8) 6454 6667
Email info@impactminerals.com.au www.impactminerals.com.au
Part of the 1.2 metre intercept of exceptional PGM mineralisation
Six other drill holes of the 13 mineralised holes completed by Impact at Red Hill returned anomalous
cobalt grades of 0.01% to 0.03% up to 20 metres thick. Intercepts include Hole RHDH001 that returned:
1.9 m at 0.1% cobalt, 2.0% copper 1.2% nickel, 1.1 g/t platinum, 3.4 g/t palladium, 0.2 g/t gold and
15 g/t silver from 53.7 metres down hole;
and Hole RHDH006 which returned:
5.2 m at 0.06% cobalt 1.1% copper 1.6% nickel 0.2 g/t gold 3.9 g/t palladium and 0.8 g/t platinum
from 54.2 metres down hole.
Of interest, low grade cobalt is also associated with the high grade zinc-lead silver mineralisation also
discovered by Impact at Red Hill and attests to the widespread nature of cobalt in the Broken Hill area.
Hole RHDH020 at Red Hill returned:
1.6 metres at 0.013% cobalt, 66.7 g/t silver 22% zinc and 1.6% lead.
Note that Silver City Minerals Limited holds a 20% interest in the silver-lead-zinc rights on E7390 that
hosts Red Hill, free carried to a decision to mine.
At the Platinum Springs Prospect located some 35 km north east of Red Hill, a narrow unit of massive
nickel-copper sulphide unit intersected in Impact’s drill Hole PSD02 returned:
0.6 metres at 0.16% cobalt, 7.4% nickel, 7.6% copper
11.5 g/t platinum, 25.6 g/t palladium, 1.4 g/t gold and 44.3 g/t silver.
Together, these results all show the potential for significant cobalt credits to any economic nickel-copperPGM mineralisation that may be found. Follow up drilling is required at both prospects and to this aim a
VTEM helicopter-borne geophysical survey to help identify targets for bodies of massive sulphide is due
to commence in the area next week.
For further details on these results please see the following announcements:
23 October 2015; 26 October 2015; 8 December 2015; 29 January 2016; 3 February 2016.
Figure 1. Impact’s exploration licences in the Broken Hill area showing priority cobalt targets
2. Pyrite-cobalt deposits (Big Hill style)
Although the Broken Hill region of New South Wales Australia is well known for its silver-lead-zinc
mineralisation, it is also well endowed with extensive cobalt mineralisation including the Thackaringa
Cobalt Project located 25 km west of Broken Hill and about 3 to 5 kilometres west of Impacts extensive
tenement holdings.
The Thackaringa Project has an Inferred Resource of 33 Mt at 0.08% cobalt (833 ppm) for 27,500 tonnes
of contained cobalt. The cobalt occurs within three separate layer parallel bodies of massive pyrite
(Big Hill, Pyrite Hill and Railway) along a 15 km trend of rocks in the so-called Thackaringa Group
(Figure 1 and see http://www.cobaltblueholdings.com).
An interpretation of the regional magnetic data, regional geological maps and mineral occurrence data
indicates that within the western half of Impact’s licences and to the south of the Red Hill Prospect, there
are many tens of kilometres of strike extent of the same rocks that host the Thackaringa deposits that are
prospective for cobalt (Figure 1).
There has been virtually no exploration for cobalt in these areas, much of which lies beneath a thin cover
of recent gravel. A number of occurrences of Big Hill style cobalt deposits have been mapped within,
close to or along strike from Impact’s licences and accordingly the potential for the discovery of further
mineralisation is considered high.
About 30 drill holes have been recorded by the Geological Survey of New South Wales as having
maximum intercepts of between 0.01% and 0.04% cobalt over one to two metre intercepts with maximum
intercepts of up to 0.1% cobalt. However the majority of the drill holes were shallow air core holes and
not targeted specifically at cobalt mineralisation.
A synthesis and interpretation of the scant previous exploration data in this area is underway.
The licences are currently under application and on-ground work will commence upon grant.
3. Cobalt-Copper-Iron deposits (Broken Hill Great Eastern and Sister’s Styles)
Cobalt mineralisation in the Broken Hill area is also associated with various types of ironstone and
variably with copper and sometimes gold.
Great Eastern-style deposits comprise cobalt+/-copper in magnetite ironstones recognisable as prominent
anomalies in regional magnetic data and Sisters-style deposits which comprise cobalt+/- copper in ironrich chert layers.
Four target areas for these styles of mineralisation have been identified from the previous exploration data
in the north east part of Impact’s licences (Figure 1).
Three prominent magnetic units are prospective for Great Eastern-style deposits. Two occur close to the
northern boundary of Impact’s licences and no records of significant exploration have been found for
these areas. One magnetic unit occurs south of Impact’s Little Darling Creek nickel-copper-PGM prospect
where a prominent magnetic unit has been explored for copper mineralisation (Figure 1). Anomalous
cobalt-in-soil results between 0.05% and 0.22% cobalt occur in many places within an area of several
square kilometres and drill holes have returned intercepts of up to 0.2% cobalt. The area has not been
systematically explored and a detailed review of all this data is warranted.
A number of Sisters-style mineral occurrences have been documented close to and along the Moorkai
Trend of ultramafic rocks that extends over 10 kilometres to the north west of the Platinum Springs
Prospect (Figure 1 and see announcement). There has been no exploration for cobalt in this area.
NEXT STEPS
Exploration for cobalt will be integrated into Impact’s programme of work for the other styles of
mineralisation for which the licences are prospective. A review and synthesis of the previous exploration
data within Impact’s new licence applications is underway together with an interpretation of the regional
magnetic data to better understand the distribution of the host rocks prospective for cobalt.
The VTEM survey due to commence next week will cover the Red Hill area and Little Darling Creek
Prospects in the first instance. A follow up survey over the Moorkai Trend will be completed later in the
year.
All of this data will be integrated to identify priority areas for follow up work including drilling.
Dr Michael G Jones
Managing Director
The review of exploration activities and results contained in this report is based on information compiled by Dr Mike Jones, a Member
of the Australian Institute of Geoscientists. He is a director of the company and works for Impact Minerals Limited. He has sufficient
experience which is relevant to the style of mineralisation and types of deposits under consideration and to the activity which he is
undertaking to qualify as a Competent Person as defined in the 2012 edition of the Australasian Code for Reporting of Exploration
Results, Mineral Resources and Ore Reserves (the JORC Code). Mike Jones has consented to the inclusion in the report of the matters
based on his information in the form and context in which it appears.
Impact Minerals confirms that it is not aware of any new information or data that materially affects the information included in the
previous market announcements referred to and in the case of ore reserves, that all material assumptions and technical parameters
underpinning the estimates continue to apply and have not materially changed..
APPENDIX 1 - SECTION 1 SAMPLING TECHNIQUES AND DATA
Criteria
JORC Code explanation
Commentary
Nature and quality of sampling (e.g. cut channels, random chips, or specific
specialised industry standard measurement tools appropriate to the
minerals under investigation, such as down hole gamma sondes, or
handheld XRF instruments, etc). These examples should not be taken as
limiting the broad meaning of sampling.
Rock Chip Samples
Random rock samples were taken at surface which represented favourable geology and alteration to
known mineralisation in the region. Samples are variably weathered.
Soil Samples
Soil samples were taken at 50 m intervals from a hole 15-20 deep and sieved to -2mm to collect about
250 g of material.
Diamond Drilling
Diamond drilling was used to produce drill core either with a diameter of 63.5 mm (HQ) or 47.6 mm (NQ).
A handheld XRF instrument was used to analyse the drill core at 50 cm intervals.
Include reference to measures taken to ensure sample representivity and
the appropriate calibration of any measurement tools or systems used
Rock Chip Samples
Representative rock chip samples at each sample site weigh between 0.8 and 1.2 kg. Soil samples are
taken at a consistent depth below surface and sieved.
Soil Samples and Drill Samples
Sample representivity was ensured by a combination of Company Procedures regarding quality control
(QC) and quality assurance / testing (QA).
Examples of QC include (but are not limited to), daily workplace and equipment inspections, as well as
drilling and sampling procedures.
Examples of QA include (but are not limited to) collection of “field duplicates”, the use of certified
standards and blank samples approximately every 50 samples.
Aspects of the determination of mineralisation that are Material to the
Public Report. In cases where ‘industry standard’ work has been done this
would be relatively simple (e.g. ‘reverse circulation drilling was used to
obtain 1 m samples from which 3 kg was pulverised to produce a 30 g
charge for fire assay’). In other cases more explanation may be required,
such as where there is coarse gold that has inherent sampling problems.
Unusual commodities or mineralisation types (e.g. submarine nodules) may
warrant disclosure of detailed information
Rock Chip and Diamond Drill Samples
Rock samples and split diamond core were sent to Intertek Adelaide where they were crushed, dried and
pulverised (total prep) to produce a 25-30 g sub-sample for analysis by four acid digest with an ICP/AES
finish for ore grade base metal samples and either lead collection or nickel sulphide fire assay with AAS or
MS finish for gold and the PGMs. Weathered samples contained gossanous sulphide material. Soil
samples were sent to SGS Perth for analysis by the MMI digest.
The XRF data is qualitative only. A comparison between the XRF results and wet chemical assay data will
be completed on receipt of final results.
Sampling techniques
Drilling techniques
Drill sample recovery
Drill type (e.g. core, reverse circulation, open-hole hammer, rotary air blast,
auger, Bangka, sonic, etc) and details (e.g. core diameter, triple or standard
tube, depth of diamond tails, face-sampling bit or other type, whether core
is oriented and if so, by what method, etc).
Method of recording and assessing core and chip sample recoveries and
results assessed
Diamond Drilling comprises NQ (47.6 mm diameter) and HQ (63.5 mm diameter) sized core. Impact
diamond core is triple tube and is oriented. Historical diamond core was not oriented.
Diamond core recoveries for all holes are logged and recorded. Recoveries are estimated to be
approximately >97% for the Red Hill Prospect. No significant core loss or sample recovery problems are
observed in the drill core.
Criteria
JORC Code explanation
Commentary
Measures taken to maximise sample recovery and ensure representative
nature of the samples
Diamond core is reconstructed into continuous runs on an angle iron cradle for orientation marking.
Depths are checked against the depth given on the core blocks and rod counts are routinely carried out
by the driller.
Whether a relationship exists between sample recovery and grade and
whether sample bias may have occurred due to preferential loss/gain of
fine/coarse material.
No sample bias has been established.
Logging
Geological logging of samples followed company and industry common practice. Qualitative logging of
samples included (but not limited to); lithology, mineralogy, alteration, veining and weathering. Diamond
core logging included additional fields such as structure and geotechnical parameters.
Whether core and chip samples have been geologically and geotechnically
logged to a level of detail to support appropriate Mineral Resource
estimation, mining studies and metallurgical studies.
Magnetic Susceptibility measurements were taken for each 0.5 m diamond core interval.
For diamond core, information on structure type, dip, dip direction, texture, shape and fill material has
been recorded in the logs. RQD data has been recorded on selected diamond holes. Handheld XRF
analysis was completed at 50 cm intervals on diamond core.
Whether logging is qualitative or quantitative in nature. Core (or costean,
channel, etc) photography.
All logging is quantitative, based on visual field estimates. Systematic photography of the diamond core in
the wet and dry form was completed.
All diamond drill holes were logged in full.
The total length and percentage of the relevant intersections logged
Sub-sampling techniques and
sample preparation
Detailed diamond core logging, with digital capture was conducted for 100% of the core by Impact’s onsite geologist.
If core, whether cut or sawn and whether quarter, half or all core taken.
All core samples were sampled by half core. Selected intervals of quarter core will be selected for check
assays if required.
If non-core, whether riffled, tube sampled, rotary split, etc and whether
sampled wet or dry.
No RC drilling results are reported.
For all sample types, the nature, quality and appropriateness of the sample
preparation technique.
Company procedures were followed to ensure sub-sampling adequacy and consistency. These included
(but were not limited to) daily work place inspections of sampling equipment and practices, as well as
sub-sample duplicates (“field duplicates”).
Quality control procedures adopted for all sub-sampling stages to maximise
representivity of samples.
Laboratory QC procedures for rock sample and diamond drill core assays involve the use of internal
certified reference material as assay standards, along with blanks, duplicates and replicates.
Measures taken to ensure that the sampling is representative of the in situ
material collected, including for instance results for field duplicate/secondhalf sampling.
Rock and Soil Samples
Field duplicates were taken at selected sample sites.
Criteria
Quality of assay data and
laboratory tests
Verification of sampling and
assaying
Location of data points
Data spacing and distribution
JORC Code explanation
Commentary
Whether sample sizes are appropriate to the grain size of the material being
sampled.
Diamond Core Samples
Quarter core duplicate samples are taken randomly every 50 samples. Sample sizes at Red Hill are
considered adequate due to mineralisation style.
The nature, quality and appropriateness of the assaying and laboratory
procedures used and whether the technique is considered partial or total.
An industry standard fire assay technique for samples using lead collection with an Atomic Absorption
Spectrometry (AAS) finish was used for gold and aqua regia digest for base metals and silver.
For geophysical tools, spectrometers, handheld XRF instruments, etc, the
parameters used in determining the analysis including instrument make and
model, reading times, calibrations factors applied and their derivation, etc.
No geophysical tools were used to determine material element concentrations. A handheld XRF was used
for qualitative analysis only.
Nature of quality control procedures adopted (e.g. standards, blanks,
duplicates, external laboratory checks) and whether acceptable levels of
accuracy (i.e. lack of bias) and precision have been established.
Rock Chip Samples
For the rock chips, quality control procedures for assays were followed via internal laboratory protocols.
Accuracy and precision are within acceptable limits.
Diamond Drill Samples
Reference standards and blanks are routinely inserted into every batch of samples at a rate of 1 in every
50 samples.
The verification of significant intersections by either independent or
alternative company personnel.
The results have not been verified by independent or alternative companies. This is not required at this
stage of exploration.
The use of twinned holes.
No drilling results are reported.
Documentation of primary data, data entry procedures, data verification,
data storage (physical and electronic) protocols.
Primary assay data for rock chips has been entered into standard Excel templates for plotting in Mapinfo.
All historical drill data has been entered digitally by previous explorers and verified internally by Impact.
Discuss any adjustment to assay data.
There are no adjustments to the assay data.
Accuracy and quality of surveys used to locate drillholes (collar and downhole surveys), trenches, mine workings and other locations used in Mineral
Resource estimation.
Sample locations and drill holes were located by hand held GPS.
Specification of the grid system used.
The grid system for Broken Hill is MGA_GDA94, Zone 54.
Quality and adequacy of topographic control.
Standard government topographic maps have been used for topographic validation.
For the diamond holes, down-hole single shot surveys were conducted by the drilling contractor. Surveys
were conducted at 15 m, 30 m and then approximately every 30 m down-hole.
Data spacing for reporting of Exploration Results.
Sample spacing for the soil survey was on a 50 m by 50 m grid.
Reconnaissance drill spacing is approximately 200 m.
Whether the data spacing and distribution is sufficient to establish the
degree of geological and grade continuity appropriate for the Mineral
Resource and Ore Reserve estimation procedure(s) and classifications
applied.
Estimations of grade and tonnes have not yet been made.
Criteria
JORC Code explanation
Commentary
Whether sample compositing has been applied.
Sample compositing has not been applied.
Whether the orientation of sampling achieves unbiased sampling of possible
structures and the extent to which this is known, considering the deposit
type.
Not relevant to soil and rock chip results.
The orientation of mineralisation in RHD001 yet to be determined.
If the relationship between the drilling orientation and the orientation of
key mineralised structures is considered to have introduced a sampling bias,
this should be assessed and reported if material.
Not relevant to soil and rock chip results or early stage exploration drill results.
Sample security
The measures taken to ensure sample security.
Chain of custody is managed by Impact Minerals Ltd. Samples for Broken Hill are delivered by Impact
Minerals Ltd by courier who transports them to the laboratory for prep and assay. Whilst in storage,
they are kept in a locked yard. Tracking sheets have been set up to track the progress of batches of
samples.
Audits or reviews
The results of any audits or reviews of sampling techniques and data.
At this stage of exploration a review of the sampling techniques and data by an external party is not
warranted.
Orientation of data in relation
to geological structure
SECTION 2 REPORTING OF EXPLORATION RESULTS
Criteria
JORC Code explanation
Commentary
Type, reference name/number, location and ownership including
agreements or material issues with third parties such as joint ventures,
partnerships, overriding royalties, native title interests, historical sites,
wilderness or national park and environmental settings.
The Broken Hill Project currently comprises 1 exploration licences covering 100 km2. The tenement is held
100% by Golden Cross Resources Ltd. Impact Minerals Limited is earning 80% of the nickel-copper-PGE
rights in the licence from Golden Cross. No aboriginal sites or places have been declared or recorded over
the licence area. There are no national parks over the license area.
The security of the tenure held at the time of reporting along with any
known impediments to obtaining a licence to operate in the area.
The tenement is in good standing with no known impediments.
Exploration done by other
parties
Acknowledgment and appraisal of exploration by other parties.
There has been no significant previous work at this prospect.
Geology
Deposit type, geological setting and style of mineralisation.
Nickel-copper-PGE sulphide mineralisation associated with an ultramafic intrusion.
Mineral tenement and land
tenure status
Criteria
Drill hole Information
Data aggregation methods
JORC Code explanation
Commentary
A summary of all information material to the understanding of the
exploration results including a tabulation of the following information for
all Material drill holes:
easting and northing of the drill hole collar
elevation or RL (Reduced Level – elevation above sea level in
metres) of the drill hole collar
dip and azimuth of the hole
down hole length and interception depth
hole length.
See Table in text.
In reporting Exploration Results, weighting averaging techniques, maximum
and/or minimum grade truncations (e.g. cutting of high grades) and cut-off
grades are usually Material and should be stated.
All reported assays have been length weighted. No top cuts have been applied. A cut-off of approximately
0.1% Cu, 0.4% Cu and 1.0% Cu has been applied for reporting of exploration results.
Where aggregate intercepts incorporate short lengths of high grade results
and longer lengths of low grade results, the procedure used for such
aggregation should be stated and some typical examples of such
aggregations should be shown in detail.
High grade massive sulphide intervals internal to broader zones of disseminated sulphide mineralisation
are reported as included intervals.
The assumptions used for any reporting of metal equivalent values should
be clearly stated.
No metal equivalents have been reported.
Relationship between
mineralisation widths and
intercept lengths
These relationships are particularly important in the reporting of
Exploration Results.
If the geometry of the mineralisation with respect to the drill hole angle is
known, its nature should be reported.
If it is not known and only the down hole lengths are reported, there should
be a clear statement to this effect (e.g. ‘down hole length, true width not
known’).
Diagrams
Appropriate maps and sections (with scales) and tabulations of intercepts
should be included for any significant discovery being reported These
should include, but not be limited to a plan view of drill hole collar locations
and appropriate sectional views.
Refer to Figures in body of text.
Where comprehensive reporting of all Exploration Results is not
practicable, representative reporting of both low and high grades and/or
widths should be practiced to avoid misleading reporting of Exploration
Results.
All results reported are representative
Balanced reporting
The orientation of mineralisation in RHD001 is yet to be determined.
Criteria
JORC Code explanation
Other substantive exploration
data
Other exploration data, if meaningful and material, should be reported
including (but not limited to): geological observations; geophysical survey
results; geochemical survey results; bulk samples – size and method of
treatment; metallurgical test results; bulk density, groundwater,
geotechnical and rock characteristics; potential deleterious or
contaminating substances.
Further work
The nature and scale of planned further work (e.g. tests for lateral
extensions or depth extensions or large-scale step-out drilling).
Diagrams clearly highlighting the areas of possible extensions, including the
main geological interpretations and future drilling areas, provided this
information is not commercially sensitive
Commentary
Assessment of other substantive exploration data is not yet complete however considered immaterial at
this stage.
Follow up work programmes will be subject to interpretation of results which is ongoing.
Share your feedback
Discover