Large Copper Halo identified at Apsley Prospect
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
Date: 23 August 2021
Number: 768/24082021
LARGE COPPER HALO IDENTIFIED AT THE
APSLEY PORPHYRY COPPER-GOLD PROSPECT BELT, NSW.
•
•
•
•
•
•
A large halo of copper and associated altered rocks covering a 1,000 metre by 1,000
metre sized area down to at least 350 metres below surface in places has been identified.
Up to nearly 250 metre thick intercepts averaging from 100 ppm to 200 ppm copper with
associated molybdenum and alteration typical of the outer zones of a porphyry coppergold system.
Similar copper values and alteration at the Ridgeway Mine occur within only 200 metres
to 300 metres of the high grade core.
Metal zonation patterns have identified three areas for follow up work including further
alteration mineral studies to provide more definitive vectors to ore before drilling.
COVID lockdown in NSW will curtail any activity in NSW for the remainder of the year.
Focus to move to drilling of the Doonia gold project and the Arkun nickel-copper-PGE
project in Western Australia.
Figure 1. View looking South of the copper halo (red bubbles >100 ppm copper, green bubbles >200 ppm
copper) with an associated molybdenum halo (>2 ppm molybdenum). Thick intercepts of low to modest grade
copper occur over an area of at least about one square kilometre.
A very large halo of copper has been identified in first pass, widely spaced reconnaissance drilling at
Impact Minerals Limited’s Apsley Prospect within the company’s 100% owned Commonwealth
Project in the Lachlan copper-gold province of New South Wales.
The halo may be part of the outer zone of a large alteration system around an alkaline porphyry
copper-gold deposit similar to the Ridgeway deposit (155 Mt at 0.73 g/t gold and 0.38% copper
Newcrest Mining Limited ASX: NCM)) 100 km south of Apsley and the recent Boda discovery
(Alkane Resources Limited ASX: ALK) 20 km to the north. These are both hosted by rocks of the
same age and geochemistry as at Apsley.
The halo has been defined at copper values of more than 100 ppm copper in continuous zones up to
nearly 250 metres thick and potentially extending over an area of at least 1,000 metres by 1,000 metres
in size (Figure 1, Tables 1 and 2). There are numerous thinner zones up to about 80 metres thick that
contain between 200 ppm and 250 ppm copper and these include one to four metre thick zones of
higher grades of up to 4,700 ppm copper related to zones of narrow quartz-sulphide veins. The halo
also contains widespread low-level molybdenum (Figure 1, Table 2).
The halo constitutes a significant inventory of copper and very recently published scientific work
about the Ridgeway deposit has shown that similar grades of copper up to 200 ppm define a halo that
extends only 200 metres to 300 metres away from the high grade core of the deposit (Figure 2).
From a presentation by Prof. D Cooke, Centre for Ore Deposit and Earth Science (“CODES”) at UTAS at geohug.rocks
Figure 2. Summary of the geology and copper values around the Ridgeway deposit located near Orange in
NSW. Note the very low levels of copper present in so called “unremarkable” altered rocks even as close as 200
metres to 300 metres away from the high grade core (RHS of Figure). Distinctive alteration halos only occur
within 10’s of metres thick around high grade zones. The cross section shows it would be easy to miss such a
deposit unless the drill spacing was about 200 metres between holes.
The size of the halo is also very significant given the reconnaissance nature of the drill programme
which was done at very broad spacings of many hundreds of metres between most drill holes
(Figure 1). The Ridgeway deposit, which lies 400 metres below surface, was not discovered until the
drill density was at a spacing of 200 metres by 200 metres between drill holes (Figure 2).
Accordingly there is plenty of scope to find a Ridgeway sized deposit within the copper halo at
Apsley.
THREE AREAS FOR FOLLOW UP WORK IDENTIFIED
Within the large copper halo three broad areas for follow up work (T1, T2 and T3: Figure 3) have been
identified based on zonation patterns in pathfinder and commodity metal assemblages which are being
increasingly used as vectors towards ore in exploration for porphyry copper-gold deposits. (ASX
Release 10th August 2020).
Figure 3. Maps showing the down hole traces of drill holes showing metal assemblages for coppergold (Cu-Au core) and molybdenum-tungsten-tin (Mo-W-Sn upper phyllic zone) at Apsley.
Three target areas for follow up work have been identified (T1, T2 and T3).
The drill results are presented as additive Z score indices. Z scores are a standard statistical calculation of the number of standard
deviations a raw data (assay) value is from the mean of the data. For example a Z score of 2 indicates a value 2 standard deviations
above the mean. The higher the Z score, the more anomalous the data point is with respect to the dataset. Z scores are a standard method
of normalising data so that statistically meaningful associations between datasets can be made. In this case the Z scores for individual
metals that occur within assemblages specific to the alteration zones around a porphyry copper-gold deposit are simply added together in
order to amplify the association eg molybdenum+tungsten+tin.
At Apsley, metal assemblages typical of the core (Cu-Au) and the so-called upper phyllic zone (W,
Sn, Bi) which lies directly above the core of many porphyry copper-gold deposits, can be readily
identified in the drilling data and help define the areas for follow up (Figure 3).
Follow up area T1, is a zone of overlap between the core assemblage and the upper phyllic zone
assemblage in the north west of the halo. Area T2 is a large zone defined mainly by the upper phyllic
zone and strong alteration present in Hole APIPT001 in the centre of the halo. Area T3 may represent
a target at depth in the south east corner of the halo (Figure 3).
However, the widespread nature of the drilling and also the low levels of copper and in particular gold
reported are insufficient at this stage to provide more definitive vectors to ore.
This interpretation of the zonation at Apsley is based on a widely used model for the levels of metals
present around porphyry copper-gold deposits (Figure 4). The low levels of certain metals seen in
these zones are comparable to those at Apsley (cf Table 2).
Figure 4. Image showing the interpreted geochemical zonation around porphyry copper systems based
in the Yerington district in the USA (from Cohen 2011).
Note that this model is based on a parent magma chemistry (calc-alkaline) that is different to the alkaline porphyry coppergold deposits of the Lachlan province. However the model is probably a good first order approximation although vectoring
at a more detailed scale may not be relevant. There is little published information on the trace metal distribution around
alkaline porphyry deposits.
ABOUT THE DRILL PROGRAMME
The drill programme, which comprised 17 reverse circulation (RC) scout drill holes for 4,954 metres
to depths of between 157 metres and 402 metres (Table 1), tested a number of specific coincident
geophysical IP and soil geochemistry anomalies prospective for porphyry copper-gold deposits (ASX
Releases 10th August 2020, 16th February 2021 and 12th March 2021).
Fourteen drill holes (APIPT001-014) were completed in the central part of the prospect covering an
area of about one square kilometre, and these have returned the most encouraging results which define
the copper halo (Figure 1).
The drill holes intersected a wide variety of porphyry, volcanic and variably carbonaceous and pyriterich sedimentary rocks that for the most part dip west at shallow to moderate angles. In places the
porphyry units may have a steeper dip suggesting they may be later cross-cutting intrusions (Figure 5,
ASX Release 13th April 2021). The pyrite-bearing sedimentary units were found to be the source of
the strongest IP anomalies. These rocks do not outcrop in any quantity at surface.
Figure 5. Cross section looking north through APIPT001 and 002. Note the relatively shallow dip on
the units, the thickness of the copper intercept and the possibly porphyry intrusion.
Hole APS001 intersected the most altered rocks where a 150 metre thick intercept at 150 ppm copper
in the halo is associated with a narrow possible porphyry intrusion, associated with low-level
molybdenum, at a depth of about 300 metres down hole. A weak zone of phyllic alteration parallel to
the interpreted porphyry unit may also be present (Figure 5).
The copper zone appears to be associated with a specific rock unit which is presumably more porous
than the surrounding rock units (Figure 5). This suggests that there may have been strong lateral fluid
flow of copper-bearing hydrothermal fluids along specific rock units. This may go some way to
explaining the large size of the halo in that it may represent a so-called large leakage anomaly from a
porphyry somewhere at depth or along trend. This may add to the complexity of the system in terms of
vectoring to the core.
ALTERATION MINERALS
All the different rock types within the copper halo are variably altered to chlorite, epidote and hematite
with lesser biotite and disseminated very fine grained pyrite and weak disseminated copper sulphides.
There is strong K-feldspar alteration in places, in particular in hole APIPT001 which intersected a
60 metre thick zone of more intense alteration associated with the porphyry unit (ASX Release 13th
April 2021). These assemblages are characteristic of the outer distal, or propylitic zone, of alkaline
porphyry copper-gold systems and is considered very encouraging.
Recent work has shown that hematite dusting in particular is an important indicator of the propylitic
zone around the Ridgeway deposit. Indeed this outer zone is noted as being “unremarkable,” given the
very low copper values of generally much less than 200 ppm (Figure 2) and contrasts markedly with
the well-known Northparkes alkaline porphyry copper deposit located 100 km west of Apsley which is
characterised by a wide halo of copper that extends several hundred metres away from the orebody at
levels of copper greater than 1,000 ppm.
NEXT STEPS
The Apsley target was drilled because of the strong combined geophysical and geochemical
anomalies. The results, whilst very encouraging are not as definitive as required for immediate follow
up drilling. Further drilling is required, possibly to some depth, in several areas. However, further
studies on the nature and composition of the alteration minerals are required first in order to determine
if more accurate vectors to the system’s core can be found. Discussions are in progress with CODES
to determine if this is feasible. A decision on further drilling will be made when these studies are
complete.
The current COVID lockdown situation across NSW is preventing any further on-ground work at
Impact’s two key projects in NSW, Commonwealth and Broken Hill. It is likely this will continue for
some time, and it may not be possible to drill at Broken Hill as originally hoped for.
Accordingly Impact is now focussed on progressing its proposed drill programme at the Doonia gold
project, located 25 km east of the recent Burns discovery near Kambalda in Western Australia (Lefroy
Exploration Limited ASX: LEF). Here, environmental approvals are already in place and the required
heritage survey is scheduled for September after which drilling will be possible. Advanced discussions
are in progress to secure a drill rig.
In addition the Company is now in receipt of the majority of the soil geochemistry survey results from
its Arkun project and an interpretation of this large data set is in progress with on-ground follow up
being planned for September.
Dr Michael G Jones
Managing Director
COMPETENT PERSONS STATEMENT
The review of exploration activities and results contained in this report is based on information compiled by Dr Mike Jones, a
Member of the Australian Institute of Geoscientists. He is a director of the company and works for Impact Minerals Limited.
He has sufficient experience which is relevant to the style of mineralisation and types of deposits under consideration and to
the activity which he is undertaking to qualify as a Competent Person as defined in the 2012 edition of the Australasian
Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code). Mike Jones has
consented to the inclusion in the report of the matters based on his information in the form and context in which it appears.
Table 1. Drill Hole Information
Hole ID Hole Type Grid
Easting Northing Azimuth Dip Depth
APIPT001 RC
MGA94_55 683456 6390200
90 -75 318
APIPT002 RC
MGA94_55 683306 6390235
90 -89 318
APIPT003 RC
MGA94_55 683723 6390590
90 -70 302
APIPT004 RC
MGA94_55 683934 6390595
90 -70 350
APIPT005 RC
MGA94_55 683916 6390597
270 -65 234
APIPT006 RC
MGA94_55 683502 6389791
270 -70 228
APIPT007 RC
MGA94_55 683307 6389797
70 -75 157
APIPT008 RC
MGA94_55 682305 6397528
90 -70 280
APIPT009 RC
MGA94_55 683837 6389793
80 -60 312
APIPT010 RC
MGA94_55 683900 6389600
80 -60 302
APIPT011 RC
MGA94_55 683288 6389669
170 -60 300
APIPT012 RC
MGA94_55 683602 6390396
110 -70 228
APIPT013 RC
MGA94_55 683522 6390400
110 -70 318
APIPT014 RC
MGA94_55 684140 6389609
120 -60 402
APIPT015 RC
MGA94_55 684980 6391653
90 -75 300
APIPT016 RC
MGA94_55 684969 6391653
30 -60 204
APIPT017 RC
MGA94_55 685033 6391763
55 -60 401
Table 2. Intercepts of note
APPENDIX 1 - SECTION 1 SAMPLING TECHNIQUES AND DATA FOR THE COMMONWEALTH PROJECT
Criteria
JORC Code explanation
Sampling techniques
Nature and quality of sampling (e.g. cut channels, random chips, or specific
specialised industry standard measurement tools appropriate to the
minerals under investigation, such as down hole gamma sondes, or
handheld XRF instruments, etc). These examples should not be taken as
limiting the broad meaning of sampling.
Include reference to measures taken to ensure sample representivity and
the appropriate calibration of any measurement tools or systems used
Aspects of the determination of mineralisation that are Material to the
Public Report. In cases where ‘industry standard’ work has been done this
would be relatively simple (e.g. ‘reverse circulation drilling was used to
obtain 1 m samples from which 3 kg was pulverised to produce a 30 g
charge for fire assay’). In other cases more explanation may be required,
such as where there is coarse gold that has inherent sampling problems.
Unusual commodities or mineralisation types (e.g. submarine nodules)
may warrant disclosure of detailed information
Drilling techniques
Drill sample recovery
Commentary
Reverse Circulation (RC) percussion drilling was used to produce a 1m bulk sample (~25kg) which was
collected in plastic bags. 1m split samples (nominally 3kg) were collected using a riffle splitter and
placed in a calico bag. The cyclone was cleaned out with compressed air at the end of each hole and
periodically during the drilling. Holes were drilled to optimally intercept interpreted mineralised zones.
A hand held XRF instrument was used to select areas of composite samples for assay on either a 2 metre
or 4 metre sample interval. The composite was prepared by spearing of the 1 m bulk samples using
standard techniques to ensure representivity.
Sample representivity was ensured by a combination of Company Procedures regarding quality control
(QC) and quality assurance / testing (QA).
Examples of QC include (but are not limited to), daily workplace and equipment inspections, as well as
drilling and sampling procedures. Examples of QA include (but are not limited to) collection of “field
duplicates”, the use of certified standards and blank samples approximately every 50 samples.
RC samples were submitted to Bureau Veritas in Adelaide for assay by 4 acid digest with ICP-MS finish
and Fire Assay technique (lead collection) for gold. Sample preparation involved: sample crushed to 70%
less than 2mm, riffle split off 1 kg, pulverise split to >85% passing 75 microns.
Drill type (e.g. core, reverse circulation, open-hole hammer, rotary air
blast, auger, Bangka, sonic, etc) and details (e.g. core diameter, triple or
standard tube, depth of diamond tails, face-sampling bit or other type,
whether core is oriented and if so, by what method, etc).
RC drilling comprises 4-inch hammer.
Method of recording and assessing core and chip sample recoveries and
results assessed
RC samples were visually checked for recovery, moisture and contamination as determined from
previous drill logs.
Measures taken to maximise sample recovery and ensure representative
nature of the samples
The RC samples were collected by plastic bag directly from the rig-mounted cyclone and laid directly on
the ground in rows of 10. The drill cyclone and sample buckets are cleaned between rod-changes and
after each hole to minimise down-hole and/or cross contamination.
Whether a relationship exists between sample recovery and grade and
whether sample bias may have occurred due to preferential loss/gain of
fine/coarse material.
No relationship has been established and it is considered unlikely to be a material issue.
Criteria
Logging
Sub-sampling techniques and
sample preparation
Quality of assay data and
laboratory tests
Verification of sampling and
assaying
JORC Code explanation
Whether core and chip samples have been geologically and geotechnically
logged to a level of detail to support appropriate Mineral Resource
estimation, mining studies and metallurgical studies.
Commentary
Geological logging of samples followed company and industry common practice. Qualitative logging of
samples included (but not limited to); lithology, mineralogy, alteration, veining and weathering.
Whether logging is qualitative or quantitative in nature. Core (or costean,
channel, etc) photography.
All logging is quantitative, based on visual field estimates. Systematic photography of the RC chip trays
was completed.
The total length and percentage of the relevant intersections logged
All RC chips samples were geologically logged by on-site geologists.
If core, whether cut or sawn and whether quarter, half or all core taken.
Not applicable.
If non-core, whether riffled, tube sampled, rotary split, etc and whether
sampled wet or dry.
All RC samples collected in calico bags were split using a riffle splitter. Samples were dry when sampled.
Composite samples were collected from the bulk sample bags using a poly pipe spear.
For all sample types, the nature, quality and appropriateness of the sample
preparation technique.
Company procedures were followed to ensure sub-sampling adequacy and consistency. These included
(but were not limited to), daily workplace inspections of sampling equipment and practices, as well as
sub-sample duplicates (“field duplicates”).
Quality control procedures adopted for all sub-sampling stages to
maximise representivity of samples.
Laboratory QC procedures for rock sample assays involve the use of internal certified reference material
as assay standards, along with blanks, duplicates and replicates. Impact uses field duplicates and
standards for every 1 in 50 samples and blanks every 1 in 100 samples.
Measures taken to ensure that the sampling is representative of the in situ
material collected, including for instance results for field duplicate/secondhalf sampling.
All QA/QC results were within acceptable levels of +/- 15-20%
Whether sample sizes are appropriate to the grain size of the material
being sampled.
Sample sizes are considered appropriate for the mineralisation style.
The nature, quality and appropriateness of the assaying and laboratory
procedures used and whether the technique is considered partial or total.
Industry standard fire assay and 4 acid digest analytical techniques were used. Both techniques are
considered to be almost a total digest apart from certain refractory minerals not relevant to exploration
at Apsley.
For geophysical tools, spectrometers, handheld XRF instruments, etc, the
parameters used in determining the analysis including instrument make
and model, reading times, calibrations factors applied and their derivation,
etc.
N/A
Nature of quality control procedures adopted (e.g. standards, blanks,
duplicates, external laboratory checks) and whether acceptable levels of
accuracy (i.e. lack of bias) and precision have been established.
Field duplicates: 1 in every 50 samples. Standards 1 in 50 samples. Blanks 1 in 100 samples. In addition,
standards, duplicates and blanks were inserted by the analytical laboratory at industry standard
intervals.
The verification of significant intersections by either independent or
alternative company personnel.
The results have not been verified by independent or alternative companies. This is not required at this
stage of exploration.
Criteria
Location of data points
JORC Code explanation
The use of twinned holes.
N/A
Documentation of primary data, data entry procedures, data verification,
data storage (physical and electronic) protocols.
Primary assay data for drill assays will be received digitally from the laboratory and imported into
Datashed to be combined with hole numbers and depths by Impact. Exports of data are used for
plotting results in Mapinfo, Geosoft Target and Leapfrog. Original pdf laboratory assay certificates are
saved for verification when required.
Discuss any adjustment to assay data.
There are no adjustments to the assay data.
Accuracy and quality of surveys used to locate drillholes (collar and downhole surveys), trenches, mine workings and other locations used in Mineral
Resource estimation.
Specification of the grid system used.
Quality and adequacy of topographic control.
Data spacing and distribution
Commentary
Drill holes were located by hand held GPS.
The grid system for Commonwealth is MGA_GDA94, Zone 55.
Standard government topographic maps have been used for topographic validation.
Data spacing for reporting of Exploration Results.
RC drill holes are drilled at varying spacings, orientations and depths deemed appropriate for early stage
exploration
Whether the data spacing and distribution is sufficient to establish the
degree of geological and grade continuity appropriate for the Mineral
Resource and Ore Reserve estimation procedure(s) and classifications
applied.
Estimations of grade and tonnes have not yet been made.
Whether sample compositing has been applied.
Sample compositing was done for samples outside the target ultramafic unit. This was done to provide
geochemical data that may help vector towards ore.
Whether the orientation of sampling achieves unbiased sampling of
possible structures and the extent to which this is known, considering the
deposit type.
The orientation of mineralisation is yet to be determined. A 3D review of the mineralisation is currently
underway to better interpret the orientation of mineralisation and assist follow-up drilling.
If the relationship between the drilling orientation and the orientation of
key mineralised structures is considered to have introduced a sampling
bias, this should be assessed and reported if material.
Not relevant to early stage exploration drill results. No sampling bias has been detected.
Sample security
The measures taken to ensure sample security.
Chain of custody is managed by Impact Minerals Ltd. A courier is contracted by Impact Minerals to
transport the samples from the project to the laboratory for assay. Whilst in storage, they are kept in a
locked yard. Tracking sheets have been set up to track the progress of batches of samples.
Audits or reviews
The results of any audits or reviews of sampling techniques and data.
At this stage of exploration, a review of the sampling techniques and data by an external party is not
warranted.
Orientation of data in relation
to geological structure
SECTION 2 REPORTING OF EXPLORATION RESULTS
Criteria
Mineral tenement and land
tenure status
JORC Code explanation
Commentary
Type, reference name/number, location and ownership including
agreements or material issues with third parties such as joint ventures,
partnerships, overriding royalties, native title interests, historical sites,
wilderness or national park and environmental settings.
The Commonwealth Project currently comprises 6 exploration licences covering 714 km2. The
tenements are held 100% by Impact Minerals Limited. No aboriginal sites or places have been declared
or recorded over the licence area. There are no national parks over the licence area.
The security of the tenure held at the time of reporting along with any
known impediments to obtaining a licence to operate in the area.
The tenements are in good standing with no known impediments.
Exploration done by other
parties
Acknowledgment and appraisal of exploration by other parties.
Previous work has been reported where required in accordance with the JORC Code in reports referred
to in the text.
Geology
Deposit type, geological setting and style of mineralisation.
Porphyry copper-gold deposits hosted by alkalic intrusions.
Drill hole Information
A summary of all information material to the understanding of the
exploration results including a tabulation of the following information for
all Material drill holes:
•
easting and northing of the drill hole collar
•
elevation or RL (Reduced Level – elevation above sea level in
metres) of the drill hole collar
•
dip and azimuth of the hole
•
down hole length and interception depth
•
hole length.
See Table details within the main body of this ASX Release.
In reporting Exploration Results, weighting averaging techniques,
maximum and/or minimum grade truncations (e.g. cutting of high grades)
and cut-off grades are usually Material and should be stated.
N/A
Where aggregate intercepts incorporate short lengths of high grade
results and longer lengths of low grade results, the procedure used for
such aggregation should be stated and some typical examples of such
aggregations should be shown in detail.
N/A
The assumptions used for any reporting of metal equivalent values should
be clearly stated.
No metal equivalents have been reported.
Data aggregation methods
Relationship between
mineralisation widths and
intercept lengths
These relationships are particularly important in the reporting of
Exploration Results.
If the geometry of the mineralisation with respect to the drill hole angle is
known, its nature should be reported.
If it is not known and only the down hole lengths are reported, there
should be a clear statement to this effect (e.g. ‘down hole length, true
width not known’).
The orientation of mineralisation is yet to be determined. A 3D review of the mineralisation is currently
underway to better interpret the orientation of mineralisation and assist follow-up drilling.
Criteria
Diagrams
Balanced reporting
JORC Code explanation
Commentary
Appropriate maps and sections (with scales) and tabulations of intercepts
should be included for any significant discovery being reported These
should include, but not be limited to a plan view of drill hole collar
locations and appropriate sectional views.
Refer to Figures in body of text.
Where comprehensive reporting of all Exploration Results is not
practicable, representative reporting of both low and high grades and/or
widths should be practiced to avoid misleading reporting of Exploration
Results.
All results reported are representative
Other substantive exploration
data
Other exploration data, if meaningful and material, should be reported
including (but not limited to): geological observations; geophysical survey
results; geochemical survey results; bulk samples – size and method of
treatment; metallurgical test results; bulk density, groundwater,
geotechnical and rock characteristics; potential deleterious or
contaminating substances.
Further work
The nature and scale of planned further work (e.g. tests for lateral
extensions or depth extensions or large-scale step-out drilling).
Diagrams clearly highlighting the areas of possible extensions, including
the main geological interpretations and future drilling areas, provided this
information is not commercially sensitive
Assessment of other substantive exploration data is not yet complete however considered immaterial at
this stage.
Follow up work programmes will be subject to interpretation of results which is ongoing. A 3D review of
the mineralisation is currently underway to better interpret the orientation of mineralisation and assist
follow-up drilling.
Share your feedback
Discover