Impact Acquires Majority of the Blackridge Goldfield
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
Date: 17 July 2020
Number: 687/17072020
IMPACT LOCKS DOWN THE MAJORITY OF THE BLACKRIDGE
GOLD FIELD, CLERMONT QLD.
•
Two new 100% owned applications (Pewt’s Hill and Hard Hill) for Exploration Permits
secured at the Blackridge conglomerate hosted gold project near Clermont Queensland.
•
Impact’s ground holdings now cover 150 square kilometres or about 90% of the southern
part of the larger Miclere-Blackridge gold field that produced over 300,000 ounces of gold.
•
The new licences contain ground previously held under option by Impact but which were
allowed to lapse by the previous owner.
•
At Pewt’s Hill previous work has shown that:
o gold results from large diameter Calweld drill holes showed significant increases in
grade, thickness and lateral extent in the mineralised conglomerate compared to
adjacent narrow RC drill holes. This indicates gold grades are increasing with
sample size which is encouraging for potential bulk mining;
o gold is preferentially located adjacent to faults that extend into the underlying
basement. These faults are untested anywhere on the entire Blackridge project and
are targets for epithermal style mineralisation; and
o gold bearing conglomerates are preserved beneath shallow Tertiary basalt cover
that covers a large part of the licences. These areas have never been explored for
gold.
•
At Hard Hill there has been no large diameter drilling but previous narrow RC drill holes
demonstrate:
o modest to high grades of gold are present at the target unconformity over a very
large area of 1,200 metres by 2,000 metres in dimension and down to depths of only
100 metres below surface; and
o gold occurs at least in several units well above the target unconformity horizon
which have only been sporadically sampled.
•
These results and previous bulk sampling by Impact support the company’s contention
that a significant potential bulk mining opportunity now exists at Blackridge.
26 Richardson Street West Perth Western Australia 6005
Tel +61 (8) 6454 6666 Facsimile +61 (8) 6454 6667
Email info@impactminerals.com.au www.impactminerals.com.au
Impact Minerals Limited (ASX:IPT) is pleased to announce that it has lodged two new applications for
100% owned Exploration Permits for Minerals (EPM’s) at its Blackridge gold project near Clermont in
central Queensland (Figure 1).
The applications are uncontested and upon grant, together with an existing granted EPM and one fully
granted Mining Lease, will cover an area of about 150 square kilometres. This will give Impact
ownership of about 90% of the historic Blackridge gold field which forms the southern half of the
greater Miclere-Blackridge area that produced over 300,000 ounces of gold in the late 1800’s and early
1900’s (Figure 2 and ASX release 29th May 2018).
Figure 1. Location of the Blackridge-Miclere gold field. The gold-bearing Permian units also contain
major coal deposits higher in the sequence such as Blair Athol.
The gold mined at Blackridge was in the form of coarse nuggets mined mostly underground from a two
metre thick conglomerate unit located at the basal contact (unconformity) of a sedimentary sequence of
Permian age and an older sequence known as the Anakie Metamorphics (Figure 2).
Figure 2. Geology and Impact’s tenement holdings at the Blackridge project. Note the extensive
Tertiary basalt cover that overlies the target Permian conglomerates and which have hindered
exploration.
The coarse nature of the gold in the conglomerate leads to a significant “nugget effect” in exploration
sampling and in general very large samples are required to accurately estimate the gold grade. This has
hindered modern exploration at Blackridge where standard narrow diameter reverse circulation drill
holes have been the predominant method of sampling. It is highly unlikely that assays from one metre
RC samples would be large enough to allow an accurate estimate of the true grade of gold.
Impact’s new applications cover ground previously tested by reverse circulation drilling at Hard Hill
(reported previously) and by reverse circulation and large diameter (95 cm) Calweld drilling at Pewt’s
Hill (reported here for the first time, see Tables at the end of this report).
The Calweld drilling with its larger samples shows a significant increase in the grade, thickness and
lateral extent of gold mineralised intervals compared to adjacent reverse circulation drill holes. This is
very encouraging for further exploration in the broader project area given the widespread occurrence of
robust widths and grades of gold returned from the previous RC drilling.
Impact’s Strategy at Blackridge
Impact has been actively exploring at Blackridge since mid 2018 following an option agreement with
Rock Solid Holdings Pty Ltd (Rock Solid) to acquire a 95% interest in one EPM and four mining lease
applications (ASX Release 29th May 2018). Impact’s option with Rock Solid expired in late 2019
because the original option agreement could not be renegotiated to account for trial mining (ASX
Release 28th November 2019). Rock Solid allowed its EPM to lapse earlier this year and this area is
now covered by one of Impact’s new licences, EPM27571. The four mining lease applications are still
held by Rock Solid.
Impact’s strategy at Blackridge was to undertake trial mining of the conglomerate to determine the
potential for larger scale bulk mining. This followed two successful bulk sampling programmes which
returned an average grade of 0.36 grams per cubic metre over significant strike lengths (which included
samples taken on the four mining lease applications (ASX Release 18th September 2019).
The bulk samples demonstrated that two unique geological features have combined at Blackridge to
offer a potential large bulk mining opportunity. First there is a large volume of very weathered oxide
material that is soft and very easy to dig. Secondly the oxide material contains gold with exceptional
recoveries of at least 95% and probably as high as 98% using simple wet gravity processing techniques.
Accordingly, the oxide material could potentially be cheap to mine and process at low cut off grades in
the first instance (ASX Release 18th September 2019).
The bulk mining concept was further supported by the recognition by previous explorers in reverse
circulation drilling of gold bearing units well above the basal two metre zone that had been mined
historically, and, the presence of gold bearing conglomerates down dip for over 2 kilometres of strike to
a depth of only 100 metres below surface (ASX Release 29th May 2018 and 23rd October 2018).
Impact’s new applications now cover the majority of this deeper ground containing the mineralised
conglomerates thus opening up the opportunity for the company to reconsider the potential for large
scale open pit mining at Blackridge.
About the New Licences
1. Pewt’s Hill Licence (EPM27410)
The Pewt’s Hill licence covers one sub-block between the Blackridge and Springs Trends which
includes the Pewt’s Hill Prospect and four sub-blocks to the north-east (Figure 2).
Only the Pewt’s Hill area has been explored previously. It comprises a ridge of conglomerate that is
1,000 metres long and up to 350 metres wide that rises above the surrounding Tertiary basalt. The
unconformity is present at surface on the eastern side of the ridge (Figure 3).
There are areas of extensive historic mine shafts both close to the unconformity and further up in the
sedimentary sequence to the west. In addition, there is a zone of topsoil in the south east that contains
extensive nuggets and has been prospected in recent decades (Figure 3).
Figure 3. Geology and drill hole locations of the Pewt’s Hill Prospect showing areas of previous mining
and recent surficial gold accumulation. Cross sections shown in Figure 4 are highlighted in blue.
Four reverse circulation (RC) drill holes (PH01-04) and seven large diameter (95 cm) Calweld drill
holes (PHC1-7) were completed in 1987 and 1988 by Denison Resources Limited (Figures 3 and 4).
This is the first time these results have been reported under JORC 2012 code and details of the drill
holes and assays are summarised in the tables at the end of this report. Sampling details are reported in
the JORC Table and gold results are presented in Figure 4.
Figure 4. Cross sections through the Pewt’s Hill prospect (see Figure 3 for locations). Note the
increased thickness, grade and lateral extent of gold demonstrated by the Calweld drill holes in
comparison to the RC drill holes.
Reverse circulation hole PH02 intersected significant gold associated with an interpreted fault and was
twinned with Calweld drill hole PHC1. PH02 returned an intercept of 6 metres at 0.38 g/t gold
(2.28 gram.metres) and PHC1 returned 9.8 metres at 0.6 g/t gold (5.88 gram.metres).
That is, the mineralised intercept in the Calweld drill hole was nearly 50% thicker and returned 2.6
times the gold content on a gram-times-metre basis.
All the Calweld drill holes returned increased widths and grades of gold when compared to the RC
results and also significantly increased the lateral extent of the gold bearing units (Figure 4).
This is a significant result because this is the only location in the entire Blackridge project area where
this type of comparison has been done. It is clear that the RC drill holes have significantly under
estimated the grade and thickness of gold. The implication is that as sample size increases, the gold
grade and contained gold within the conglomerate units may also increase significantly.
A careful study of Figure 4 also shows that the best gold results are adjacent to a significant fault which,
along with gold in places, extends into the underlying basement and that the gold grade decreases away
from the fault. This suggests that the gold may be related to hydrothermal fluids that have migrated out
of the fault and into the surrounding conglomerate. This has also been suggested for the main producing
areas at Blackridge (ASX Release 29th May 2018). These faults have never been explored for gold
anywhere in the Blackridge area.
In addition, it is evident that the Permian conglomerate units extend at depth beneath overlying younger
Tertiary basalt cover. The basalt covers an extensive area around Blackridge and may overlie a
significant amount of Permian sedimentary units (Figure 2). These areas have never been explored and
greatly increases the search space for gold within Impact’s licences.
2. Hard Hill (EPM27571)
The Hard Hill licence covers the majority of the down dip extent of the main conglomerate unit that was
mined historically at Blackridge (Figures 2 and 5). Two lines of evidence suggest that gold in this area
occurs over a very large area of at least 2,000 metres down dip from surface outcrops of the
unconformity, to a depth of only 100 metres below surface, and for at least 1,200 metres along trend
(Figures 5 and 6).
First, a compilation of previous production data from the many shafts at Blackridge completed by
Impact has defined the higher grade runs or leads that were mined historically. These leads are quite
robust and are up to 200 metres wide and extend down dip for at least 1,500 metres in places. They
were mined mostly at grades of between 10 g/t to 20 g/t but occasionally at higher grades of up to
several ounces per tonne (Figure 5 and ASX Release 23rd October 2018). The runs are open in many
directions on the Hard Hill application and have not been followed up (Figure 5).
Secondly, extensive RC drilling by Denison Resources Limited (Denison) in the late 1980’s
demonstrated the presence of reasonably continuous gold-bearing sedimentary units over a distance of
1,200 metres on a cross-section which itself lies about 2,000 metres down dip to the northwest from the
surface outcrops (Figures 5 and 6 and ASX Release 29th May 2018).
Figure 5. Geology of the Blackridge gold field showing interpreted leads of high grade gold and
previous RC drill holes.
Evidently the conglomerate that hosts the gold is present over a very large area within Impact’s licences.
Gold grades reported by Denison in the basal units near the unconformity of up to 1 m at 11.9 g/t gold
are good evidence for high grade zones at depth at Blackridge. In addition, there is significant potential
closer to surface for gold hosted by carbonaceous black shale horizons which returned calculated gold
grades from rotosluicing of the RC samples of up to 2 m at 12.6 g/t gold (Figure 6, JORC Table and
ASX Release 29th May 2018).
In addition the time and cost involved in the nature of the sampling caused Denison to be selective in
their sampling and there are clear indications in Figure 6 of multiple gold-bearing horizons that have not
been sampled
(Figure 6 also shows a comparison of the calculated gold grades and the fire assay results for the same
sample intervals and demonstrate a signifcant nugget effect - see ASX Release 29th May 2018 for a
detailed discussion and details on the sampling procedures).
.
Figure 6. Cross-section from Figure 5 showing the results of RC drilling at Blackridge. Note that goldbearing units occur over a distance of about 1.2 kilometres in a broad palaeochannel or depocentre and
that there are multiple gold-bearing units within the sedimentary package.
Next Steps
Impact’s current focus is on its upcoming drill programme at Broken Hill which is scheduled to start
before the end of July. However, the Company’s review of the Blackridge exploration data has shown
that it is highly probable that previous work may have significantly underestimated the amount of gold
present at Blackridge and that higher grades may be delineated with an appropriate sampling
methodology.
New techniques and procedures for mining nuggetty conglomerate-hosted gold are currently being
pioneered by Novo Resources Corporation in the Pilbara region of Western Australia with good success.
Impact has been following Novo’s progress closely and is now formulating plans to emulate this work at
Blackridge. On ground work will commence on grant of the new licences expected later in 2020.
COMPLIANCE STATEMENT
This report contains Exploration Results for 11 drill holes not previously reported in accordance with
the JORC 2012 Code.
Dr Michael G Jones
Managing Director
The review of exploration activities and results contained in this report is based on information compiled by Dr Mike Jones, a Member of
the Australian Institute of Geoscientists. He is a director of the company and works for Impact Minerals Limited. He has sufficient
experience which is relevant to the style of mineralisation and types of deposits under consideration and to the activity which he is
undertaking to qualify as a Competent Person as defined in the 2012 edition of the Australasian Code for Reporting of Exploration Results,
Mineral Resources and Ore Reserves (the JORC Code). Dr Jones has consented to the inclusion in the report of the matters based on his
information in the form and context in which it appears.
Impact Minerals confirms that it is not aware of any new information or data that materially affects the information included in the
previous market announcements referred to and in the case of mineral resource estimates, that all material assumptions and technical
parameters underpinning the estimates continue to apply and have not materially changed.
Pewt’s Hill Drill Hole Table
Hole
ID
Drill
type
PH 01
RC
PH 02
PH 03
PH 04
RC
RC
RC
PHC 1
PHC 2
PHC 3
PHC 4
PHC 5
PHC 6
PHC 7
Calweld
Calweld
Calweld
Calweld
Calweld
Calweld
Calweld
Prospect
Black
Gully
Black
Gully
Pink Hill
Pink Hill
Black
Gully
Pink Hill
Pink Hill
Pink Hill
Pewts Hill
Pewts Hill
Pewts Hill
Easting Northing Azimuth Dip Depth
561206
7494787
0
-90
29
561301
561350
561303
7494888
7494991
7495080
0
0
0
-90
-90
-90
30
32
17
561281
561301
561271
561223
561355
561419
561474
7494890
7499002
7495104
7495180
7494803
7494723
7494649
0
0
0
0
0
0
0
-90
-90
-90
-90
-90
-90
-90
17
15
16
21
15
15
12
Pewt’s Hill Assay Table
Hole
ID
Sample
No.
DEPTH
TO
metres
PHC1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2.0
2.9
3.9
5.0
5.7
7.0
8.8
9.0
10.0
11.0
11.9
12.9
13.0
15.1
16.0
FIRE
ASSAY
grams
1ST
PANNING
grams
0.0254
0.0233
0.0699
0.1915
1.3671
1.0095
0.0156
0.8615
1.0905
0.4663
0.4514
1.3208
2ND
PANNING
grams
RETORT NUGGETS GRADE
grams
grams
g/t
0.018
0.017
0.043
0.108
0.976
0.778
0.583
0.615
0.779
0.333
0.322
0.943
Sample
No.
DEPTH
TO
metres
FIRE
ASSAY
grams
17
17.0
0.4785
PHC2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1.0
1.9
2.9
3.9
4.9
5.9
6.9
7.9
8.9
9.8
10.8
12.2
13.2
14.2
15.2
PHC3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0.9
1.8
2.8
4.1
5.0
6.0
7.0
8.0
9.0
10.0
10.9
12.0
13.0
14.0
15.0
16.4
1
2
3
4
5
6
1.0
2.1
3.0
4.0
5.0
6.0
Hole
ID
PHC4
1ST
PANNING
grams
2ND
PANNING
grams
RETORT NUGGETS GRADE
grams
grams
g/t
0.342
0.0309
0.0017
0.0830
0.0014
0.0250
0.0038
0.2310
0.0483
0.0640
0.1277
0.3329
0.0157
0.0480
0.0768
0.0855
0.0157
0.0174
0.036
0.0169
0.1091
0.022
0.001
0.002
0.001
0.018
0.003
0.165
0.035
0.048
0.091
0.338
0.011
0.034
0.056
0.005
0.0161
0.0105
0.025
0.013
0.03
0.017
0.129
0.899
0.1
0.044
0.064
0.104
0.012
0.015
0.0118
0.0035
0.0026
0.0529
0.0049
0.0007
0.008
0.003
0.002
0.036
0.004
0.001
0.1237
0.1399
0.0618
0.0895
0.1460
0.0210
0.0003
0.0056
0.0063
0.0114
0.0151
0.0020
Sample
No.
DEPTH
TO
metres
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
7.1
8.0
9.0
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1.3
2.1
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.1
11.0
12.0
13.1
14.0
15.0
1
2
3
4
5
6
7
8
1.1
2.0
3.0
4.0
5.0
6.0
7.0
8.0
Hole
ID
PHC5
PHC6
FIRE
ASSAY
grams
1ST
PANNING
grams
0.0060
0.0010
0.0004
0.0436
0.0655
0.0089
0.0041
0.0132
0.0257
0.0100
0.0255
0.0650
0.2552
0.6630
0.0450
2ND
PANNING
grams
0.0089
0.0047
0.001
0.0031
0.0004
0.0088
0.0094
0.0181
0.009
0.005
0.001
0
0.031
0.047
0.004
0.004
0.009
0.01
0.016
0.019
0.047
0.195
0.06
0.032
0.0066
0.005
0.0163
0.0131
0.0276
0.1323
0.0142
0.0211
0.0264
0.0534
0.012
0.010
0.025
0.095
0.012
0.017
0.022
0.039
0.157
0.053
0.101
0.062
0.060
0.2045
0.0705
0.2352
0.0772
0.0702
0.0413
0.0061
RETORT NUGGETS GRADE
grams
grams
g/t
0.0074
0.0005
0.0004
0.0080
0.0013
0.0023
0.0017
0.0005
0.0158
0.0041
0.0176
0.0093
0.0003
0.035
0.005
Hole
ID
PHC7
Sample
No.
DEPTH
TO
metres
9
10
11
12
13
14
15
9.0
10.0
11.0
12.0
13.0
14.1
15.1
1
2
3
4
5
6
7
8
9
10
11
12
1.1
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
11.5
HOLE
NO.
SAMPLE
INTERVAL
PH 01
0-1.75
1.75-16
16-24
24-29
22-23
23-24
24-25
25-26
26-27
27-28
28-29
PH 02
0-1.75
1.75-3
3-6
NUMBER
OF
COLOURS
4
3
13
3
1
1
1
FIRE
ASSAY
grams
1ST
PANNING
grams
2ND
PANNING
grams
RETORT NUGGETS GRADE
grams
grams
g/t
0.0224
0.0186
0.0033
0.0101
0.0119
0.0022
0.0034
0.0082
0.0031
0.018
0.021
0.047
0.038
0.067
0.061
0.029
0.0105
0.0017
0.0148
0.0025
0.0039
0.1090
0.0803
0.0983
0.0450
0.0017
0.0013
0.009
0.002
0.011
0.002
0.003
0.078
0.243
0.085
0.067
0.036
0.042
0.042
0.0533
0.0513
0.0909
0.077
0.0188
0.0453
0.0487
0.0536
0.0272
GRADE
g/t
0.063
0.316
0.314
0.102
0.102
0.068
0.0804
0.0206
0.0032
0.0023
0.0052
0.8024
0.331
6-12
12-16
16-29
3-4
4-5
6-7
7-8
9-10
10-11
11-12
12-13
13-14
14-15
15-16
16-17
PH 03
0.484
0.161
0.081
0.037
0.589
0.449
0.898
0-1.75
1.75-4
4-8
8-34
0-1.75
1-75-3
4-5
5-6
6-7
4-8
PH04
2
2
2
1
1
5
14
16
29
13
2
1
NSR
1
1
1
2
2
0.271
0.307
APPENDIX 1 - SECTION 1 SAMPLING TECHNIQUES AND DATA
Criteria
JORC Code explanation
Commentary
Nature and quality of sampling (e.g. cut channels, random chips,
or specific specialised industry standard measurement tools
appropriate to the minerals under investigation, such as down
hole gamma sondes, or handheld XRF instruments, etc). These
examples should not be taken as limiting the broad meaning of
sampling.
Historical RC Drilling
15 cm diameter Reverse Circulation (RC) percussion drilling was used to produce a 1m bulk sample (~25kg) which was collected
and a 25% representative 1m split samples were retained for reference. The remaining 75% sample was weighed and processed
through gravity techniques and a rota sluice to obtain a total heavy mineral concentrate. These concentrates were carefully
hand panned to produce a panned concentrate which was hand sorted to recover the gold. The recovered gold was weighed
with a 5 decimal point balance to achieve gold grades.
Historical Calweld Drilling
95cm diameter Calweld drilling was used to produce 1 1m bulk sample. Each sample represented 0.71m3 and, assuming a bulk
density of 2, each sample was therefore 1.4 tonnes. The samples were processed through a Universal Mining Fabrication
washing plant by White Industries Pty Ltd. Each sample filled the hopper. The concentrates obtained from the plant were
panned and re-panned to produce pan concentrates from which gold particles were hand picked under binocular microscope
and weighed to the fourth decimal place on an electric balance. The concentrates were sent to Pilbara Laboratory in Townsville
for fire assay.
Include reference to measures taken to ensure sample
representivity and the appropriate calibration of any
measurement tools or systems used
Historic Drill Samples
QAQC methods were not recorded by Denison Resources Limited (Denison). This is not material to the Exploration Results
reported here.
Nuggets
Previous records indicate zones of preferential nugget accumulation within sedimentary units. The distribution of such units is
not yet known in detail.
Sampling techniques
Aspects of the determination of mineralisation that are Material
to the Public Report. In cases where ‘industry standard’ work has
been done this would be relatively simple (e.g. ‘reverse
circulation drilling was used to obtain 1 m samples from which 3
kg was pulverised to produce a 30 g charge for fire assay’). In
other cases more explanation may be required, such as where
there is coarse gold that has inherent sampling problems.
Unusual commodities or mineralisation types (e.g. submarine
nodules) may warrant disclosure of detailed information
Drilling techniques
Drill sample recovery
RC and diamond drill samples
A selection of Calweld samples were assayed for gold by screen fire assay on +80# and -80# screen fractions to 0.01 g/t
detection limit.
Drill type (e.g. core, reverse circulation, open-hole hammer,
rotary air blast, auger, Bangka, sonic, etc) and details (e.g. core
diameter, triple or standard tube, depth of diamond tails, facesampling bit or other type, whether core is oriented and if so, by
what method, etc).
Drilling was completed by RC and Calweld. All holes were drilled vertically
Method of recording and assessing core and chip sample
recoveries and results assessed
RC sample recovery was not recorded by Denison. There is a strong possibility that fine gold may have been lost in the RC
drilling dust and that the recovery of coarse heavy nuggets may have been poor. This was not quantified by previous explorers.
Measures taken to maximise sample recovery and ensure
representative nature of the samples
Not recorded by Denison. Sample recovery is an important factor in exploration for gold with a strong nugget effect.
Criteria
JORC Code explanation
Whether a relationship exists between sample recovery and
grade and whether sample bias may have occurred due to
preferential loss/gain of fine/coarse material.
Logging
Sub-sampling
techniques and
sample preparation
Quality of assay data
and laboratory tests
Whether core and chip samples have been geologically and
geotechnically logged to a level of detail to support appropriate
Mineral Resource estimation, mining studies and metallurgical
studies.
Commentary
Not recorded by Denison. This is not material to the Exploration Results reported here.
Geological logging by Denison included lithology and number of gold colours
Whether logging is qualitative or quantitative in nature. Core (or
costean, channel, etc) photography.
Logging by Denison is quantitative, based on visual field estimates.
The total length and percentage of the relevant intersections
logged
All RC chips samples were geologically logged by Denison’s on-site geologist on a 1m basis in the field.
If core, whether cut or sawn and whether quarter, half or all core
taken.
No diamond drilling by Denison.
If non-core, whether riffled, tube sampled, rotary split, etc and
whether sampled wet or dry.y
The method of splitting RC samples was not recorded by Denison. This is not material to the Exploration Results reported here.
For all sample types, the nature, quality and appropriateness of
the sample preparation technique.
Not recorded by Denison. This is not material to the Exploration Results reported here.
Quality control procedures adopted for all sub-sampling stages
to maximise representivity of samples.
The QC procedure for historical RC samples is unknown but considered immaterial.
Measures taken to ensure that the sampling is representative of
the in situ material collected, including for instance results for
field duplicate/second-half sampling.
Not recorded by Denison. This is not material to the Exploration Results reported here.
Whether sample sizes are appropriate to the grain size of the
material being sampled.
Sample sizes taken by Denison are considered by Impact to be insufficient to accurately determine grade.
The nature, quality and appropriateness of the assaying and
laboratory procedures used and whether the technique is
considered partial or total.
For geophysical tools, spectrometers, handheld XRF instruments,
etc, the parameters used in determining the analysis including
instrument make and model, reading times, calibrations factors
applied and their derivation, etc.
The quality of historical drill sample assays is unknown, however this is considered immaterial at this stage of exploration.
No geophysical tools were used by Denison to determine material element concentrations.
Criteria
Verification of
sampling and
assaying
Location of data
points
Data spacing and
distribution
Orientation of data in
relation to geological
structure
Sample security
JORC Code explanation
Commentary
Nature of quality control procedures adopted (e.g. standards,
blanks, duplicates, external laboratory checks) and whether
acceptable levels of accuracy (i.e. lack of bias) and precision have
been established.
The quality control of historical drill sample assays is unknown, however this is not material to the Exploration Results reported
here.
The verification of significant intersections by either independent
or alternative company personnel.
Significant intersections from drilling have not been verified by independent or alternative companies. This is not required at
this stage of exploration.
The use of twinned holes.
Hole PCH1 (Calweld) and PH 02 (RC) are twinned holes by two different methods which showed a significant nugget effect and
suggested grades could be considerably upgraded with larger samples
Documentation of primary data, data entry procedures, data
verification, data storage (physical and electronic) protocols.
Historic drill data has not been captured digitally
Discuss any adjustment to assay data.
No significant adjustments have been required.
Accuracy and quality of surveys used to locate drill holes (collar
and down-hole surveys), trenches, mine workings and other
locations used in Mineral Resource estimation.
All historical data was in grid format. Historical ML licence boundaries were downloaded from GeoResGlobe and maps were
georeferenced to historical boundaries in MGA_GDA 94, Zone 55
Specification of the grid system used.
The grid system for Clermont is MGA_GDA94, Zone 55.
Quality and adequacy of topographic control.
Standard government topographic maps have been used for topographic validation.
Vertical historic RC drill holes do not have downhole survey data.
Data spacing for reporting of Exploration Results.
Drill spacing of drill holes ranges between 50 and 200 m which is considered adequate for Exploration Results.
Whether the data spacing and distribution is sufficient to
establish the degree of geological and grade continuity
appropriate for the Mineral Resource and Ore Reserve estimation
procedure(s) and classifications applied.
Drill spacing of drill holes ranges between 50 m and 100 m may be considered adequate for Mineral Resource and Ore reserve
estimation procedures. However estimations of grade and tonnes have not yet been made since the historic sampling
procedures are considered by Impact to be inadequate at this stage.
Whether sample compositing has been applied.
Sample compositing has been applied for quoting drill composite results only.
Whether the orientation of sampling achieves unbiased sampling
of possible structures and the extent to which this is known,
considering the deposit type.
Vertical drilling is oriented sub-perpendicular to the flat-lying mineralised trend and stratigraphic contacts as determined by
field data and cross section interpretation.
If the relationship between the drilling orientation and the
orientation of key mineralised structures is considered to have
introduced a sampling bias, this should be assessed and reported
if material.
No significant sample bias has been identified from drilling as yet due to the optimum drill orientation described above.
The measures taken to ensure sample security.
Security of historic drill samples is unknown however is considered immaterial.
Criteria
Audits or reviews
JORC Code explanation
The results of any audits or reviews of sampling techniques and
data.
Commentary
Not completed
SECTION 2 REPORTING OF EXPLORATION RESULTS
Criteria
Mineral tenement and land
tenure status
JORC Code explanation
Type, reference name/number, location and ownership including
agreements or material issues with third parties such as joint ventures,
partnerships, overriding royalties, native title interes
Share your feedback
Discover